Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
Here down the page you'll find additional reliable help and advice in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the task can relocate rapidly; if you need to open a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have certified on your own for the job as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly aid you install a new bathtub in your restroom if you have already gotten a brand-new bathtub and also don't need to change the arrangement of your previous supply of water pipelines.
Your devices and also product list need to consist of the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the spirit level reads degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been used at least once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Protect the tap in position with the supplier supplied backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that entry about How to Install a Bathtub when doing a lookup on the search engines. Sharing is caring. Who knows, you might be helping someone out. Kudos for your time. Come back soon.
Check Us Out Report this page